great charger
I received it around 3 days after purchasing
No complaints
Great for model building
Habituellement prête en 4 heures
Commander par téléphone ? Appelez-nous maintenant.
1-800-905-0410Learn more about our Price match policy
Works perfect for me bought 1/2 inch use reducers if need even used on rotor screws using reducer to 1/4 socket
This Shake'n Break gets the job done, however the square 3/8 shaft is too short and should be a little bit longer. So it bottoms out inside the female square hole. Instead the hardened tool bottoms out the flat outer surface on extensions. From the impact it mushrooms the female side of the extensions causing it to non usable again.
Prblly a good 50 set screws in and still in good shape. I use this almost explusivly for removing set screws on brake rotors. Perfect to get the impact on the screw and crack it loose in the same motion with a 19mm wrench on the tool. Hasn't let me down yet. Worth the money.
I used it on a large phillips head screw that holds the tailgate onto my 1970 International Scout. I beat on that bolt with an impact driver for two days with every penetrating spray you can think of. I was going to weld a bolt to it but figured that I would give this a try. It worked like a charm and I could not be happier. Every north east old car guy (or girl) should have one of them in the tool box.
Worked like a charm to remove Brake Bleeders on a 16 year old car in the Rust Belt where the bleeders had NEVER been touched!
Was able to flush out the old fluid. Without this I would have had to replace all four calipers!
Works perfect for me bought 1/2 inch use reducers if need even used on rotor screws using reducer to 1/4 socket
This Shake'n Break gets the job done, however the square 3/8 shaft is too short and should be a little bit longer. So it bottoms out inside the female square hole. Instead the hardened tool bottoms out the flat outer surface on extensions. From the impact it mushrooms the female side of the extensions causing it to non usable again.
Prblly a good 50 set screws in and still in good shape. I use this almost explusivly for removing set screws on brake rotors. Perfect to get the impact on the screw and crack it loose in the same motion with a 19mm wrench on the tool. Hasn't let me down yet. Worth the money.
I used it on a large phillips head screw that holds the tailgate onto my 1970 International Scout. I beat on that bolt with an impact driver for two days with every penetrating spray you can think of. I was going to weld a bolt to it but figured that I would give this a try. It worked like a charm and I could not be happier. Every north east old car guy (or girl) should have one of them in the tool box.
Worked like a charm to remove Brake Bleeders on a 16 year old car in the Rust Belt where the bleeders had NEVER been touched!
Was able to flush out the old fluid. Without this I would have had to replace all four calipers!
Works perfect for me bought 1/2 inch use reducers if need even used on rotor screws using reducer to 1/4 socket
This Shake'n Break gets the job done, however the square 3/8 shaft is too short and should be a little bit longer. So it bottoms out inside the female square hole. Instead the hardened tool bottoms out the flat outer surface on extensions. From the impact it mushrooms the female side of the extensions causing it to non usable again.
Prblly a good 50 set screws in and still in good shape. I use this almost explusivly for removing set screws on brake rotors. Perfect to get the impact on the screw and crack it loose in the same motion with a 19mm wrench on the tool. Hasn't let me down yet. Worth the money.
I used it on a large phillips head screw that holds the tailgate onto my 1970 International Scout. I beat on that bolt with an impact driver for two days with every penetrating spray you can think of. I was going to weld a bolt to it but figured that I would give this a try. It worked like a charm and I could not be happier. Every north east old car guy (or girl) should have one of them in the tool box.
Worked like a charm to remove Brake Bleeders on a 16 year old car in the Rust Belt where the bleeders had NEVER been touched!
Was able to flush out the old fluid. Without this I would have had to replace all four calipers!
Inscrivez-vous pour recevoir les derniers guides et offres spéciales dans votre boîte de réception.
1-800-905-0410 (sans frais)
support@mprtools.com
Horaires d'ouvertures
Du lundi au vendredi : de 8 h 00 à 17 h 00 HE
Sam & Dim: Fermé
great charger
I received it around 3 days after purchasing
No complaints
Great for model building